bst365最新正规买球

Evoqua United States - Canada - EN

Ionpure G2 2Amp Power Controller

Material: W2T388687 Unit of Measure #: EA See All Power Components Current Models

G2 power controller for use with IONPURE continuous electrodeionization
modules. The DC power controllers allow independent control of each IONPURE CEDI module for optimum system performance. Individual, pre-engineered boards reduce system cost, spare part cost, and simplify power supply maintenance. 

List Price
${{finalPrice | intlNumber('en-EN','USD')}}
  • 0 is the minimum order quantity for this product. Please check quantity and add to cart again.
-
+
Discontinued product
evoqa

G2 power controller for use with IONPURE continuous electrodeionization
modules. The DC power controllers allow independent control of each IONPURE CEDI module for optimum system performance. Individual, pre-engineered boards reduce system cost, spare part cost, and simplify power supply maintenance. 

List Price
${{finalPrice | intlNumber('en-EN','USD')}}
-
+
Discontinued product

Description

The G2 DC Power Controller is a modern and highly reliable solid state rectifier that will succeed the existing single-phase and three-phase IONPURE DC power controllers. A single board takes the place of six previous models, and can be used with MX, LX and VNX IONPURE CEDI modules.

The new G2 Power Controller can be a retrofit for the single-phase 200VDC, 400VDC and 600VDC IONPURE PCBs. While it is compatible with the IONPURE DSP1, DSP1P, DSP8 and DSP8P display boards, advanced control and monitoring features will be available with the release of the G2 display, employing Modbus RTU communication protocol. 

Product Information

Legacy Part Number

IP-POWER600-G2

Features

  • Modern, highly reliable high frequency design with filtered output
  • Microprocessor controlled unit
  • On-board diagnostics
  • Universal AC input voltage and frequency
  • Constant current operation
  • 0-5 VDC analog input for DC output current control
  • Analog output signals for remote monitoring (PLC or DCS)
  • Automatic power stage shutdown protections:
    • Input over-voltage and under-voltage
    • Unit over-temperature
    • Fail-safe DC power shutdown at open "Remote on/off" interlock
  • Additional protections:
    • Input transient
    • Output over-voltage
    • Output over-current and short-circuit
  • Several units can be fed from a single transformer secondary
  • Multiple transformer secondary voltage taps not required
  • Every board subjected to extended factory burn-in

Electrical Specifications

AC Input:

  • Universal voltage: 220-660 VAC ±10%
  • Single Phase
  • Frequency range: 50/60 Hz ±3%

DC Output:

  • Output voltage range: 30-600 VDC (maximum DC output voltage is approximately 90% of RMS AC input voltage at light load)
  • Output current range: 0-13.2 ADC
  • Constant current mode of operation with selectable DC output voltage limit

Input and Output Connectors:

  • AC Input terminals
  • Analog input: 0-5VDC (for DC output current control)
  • Remote on/off interlock input (dry contact)
  • DC output terminals (+, - and ground)
  • Analog outputs: 0-5VDC (for voltage and current monitoring)
  • N.O. relay output ("Output ON" indicator)

Protections:

  • Soft- start
  • Selectable current range: 0-2.5, 0-4, 0-6.5, 0-10 and 0-13.2 Amps
  • Transient voltage, over-voltage, over- temperature and short-circuit protections
  • Shutdown at open interlock

Mechanical:

  • Touch-safe connectors
  • On-board cooling fans. Ambient temperature lower than 50° C (122° F) is required

LED Indicators:

  • Output ON
  • Fault (e.g. high voltage, low voltage, communications loss, e tc.)

Standards:

  • UL recognized component (US and Canada)
  • CE
  • RoHS compliance

Environmental Requirements

  • Operating temperature: 0–50 C° (32–122° F)
  • Storage temperature: -10–70 C° (14–158° F)
  • Humidity: 0-95% (non-condensing)

Physical Specifications

  • Length: 6.12 in (155.58 mm)
  • Width: 6.00 in (152.4 mm)
  • Depth: 6.56 in (166.64 mm)
  • Weight: 6.3 lb (2.9 Kg)

Compatibility

All current IONPURE® system display boards are compatible:

  • IP-DSP1
  • IP-DSP8
  • IP- DSP1P
  • IP-DSP8P

Note: Use ONLY LX patch cables IP- LXCABLE06, IPLXCABLE10 or IP-LXCABLE16 for installation with the above display units.

Documentation